Datei:Gebhard Bosch, Lübeck. circa 1877 (01).jpg: Unterschied zwischen den Versionen

Aus Watch-Wiki
Zur Navigation springen Zur Suche springen
(German Carved Walnut Long-Running Conical Wall Regulator Clock, circa 1877 <br> Maker: Gebhard Bosch, Lübeck.<br> Description: A wonderful Victorian German long-running Conical Wall Regulator by Gebhard Bosch, Lübeck. The nicely proportioned glazed c…)
 
 
(2 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 2: Zeile 2:
 
Maker: Gebhard Bosch, Lübeck.<br>
 
Maker: Gebhard Bosch, Lübeck.<br>
 
Description: A wonderful Victorian German long-running Conical Wall Regulator by Gebhard Bosch, Lübeck. The nicely proportioned glazed case has a carved crest flanked by finials above, a hinged door with applied floral carvings, burled veneer to the backboard and a carved naturalistic curvilinear base.<br>
 
Description: A wonderful Victorian German long-running Conical Wall Regulator by Gebhard Bosch, Lübeck. The nicely proportioned glazed case has a carved crest flanked by finials above, a hinged door with applied floral carvings, burled veneer to the backboard and a carved naturalistic curvilinear base.<br>
 +
 +
Dial: The two piece porcelain dial has a sunken center, well-lettered Roman numerals for the hours, brass bezels, decorative steel-cut hands, a going bit and is signed by the maker, Gebhard Bosch, Lubeck’. Globe:The 4.5in. terrestrial globe is signed, ‘Die Erdkugal nach d neuesten und besten Quellen entworfen, Berlin, geogr. Art. Anstalt, E Schotte &  Co., Lith Bei Korbgeweit’. Movement: The movement runs just over two weeks, has thick tapered and shouldered plates secured  by massive screwed posts, a chain fusee, maintaining power, numerous end-caps with the one for the seconds shaft jeweled, high pinion counts, a conical escapement and is signed and dated on the backplate by the maker, ‘Gebhard Bosch, Lubeck, 1877’.
 +
The pendulum is suspended by a complex universal suspension that hangs from a brass bracket with adjustments for up/down, side to side and front to back. It has a steel rod, an adjustable brass weight cup, a large screwed brass adjustment weight above the universal suspension, a small globe that serves as the bob and a pointer below that interacts with the steel detent off the escapement. As the clock runs the globe rotates within the case. Notes: Family history maintains that the clock is one of three made by the maker for each of his children as wedding presents. This one was made for Marie Bosch who later settled in Scotland where it remained until the mid 90’s.
 +
 
Ref: This clock is pictured with a description in Derek Robert’s, ‘Precision Pendulum Clocks, France Germany, America and Recent Advances’, pg. 193, Fig. 35-14<br>
 
Ref: This clock is pictured with a description in Derek Robert’s, ‘Precision Pendulum Clocks, France Germany, America and Recent Advances’, pg. 193, Fig. 35-14<br>
  

Aktuelle Version vom 1. Dezember 2021, 20:06 Uhr

German Carved Walnut Long-Running Conical Wall Regulator Clock, circa 1877
Maker: Gebhard Bosch, Lübeck.
Description: A wonderful Victorian German long-running Conical Wall Regulator by Gebhard Bosch, Lübeck. The nicely proportioned glazed case has a carved crest flanked by finials above, a hinged door with applied floral carvings, burled veneer to the backboard and a carved naturalistic curvilinear base.

Dial: The two piece porcelain dial has a sunken center, well-lettered Roman numerals for the hours, brass bezels, decorative steel-cut hands, a going bit and is signed by the maker, Gebhard Bosch, Lubeck’. Globe:The 4.5in. terrestrial globe is signed, ‘Die Erdkugal nach d neuesten und besten Quellen entworfen, Berlin, geogr. Art. Anstalt, E Schotte & Co., Lith Bei Korbgeweit’. Movement: The movement runs just over two weeks, has thick tapered and shouldered plates secured by massive screwed posts, a chain fusee, maintaining power, numerous end-caps with the one for the seconds shaft jeweled, high pinion counts, a conical escapement and is signed and dated on the backplate by the maker, ‘Gebhard Bosch, Lubeck, 1877’. The pendulum is suspended by a complex universal suspension that hangs from a brass bracket with adjustments for up/down, side to side and front to back. It has a steel rod, an adjustable brass weight cup, a large screwed brass adjustment weight above the universal suspension, a small globe that serves as the bob and a pointer below that interacts with the steel detent off the escapement. As the clock runs the globe rotates within the case. Notes: Family history maintains that the clock is one of three made by the maker for each of his children as wedding presents. This one was made for Marie Bosch who later settled in Scotland where it remained until the mid 90’s.

Ref: This clock is pictured with a description in Derek Robert’s, ‘Precision Pendulum Clocks, France Germany, America and Recent Advances’, pg. 193, Fig. 35-14

Lizenz

Red copyright.svg.png Alle Bildrechte liegen bei Steven Thomson Sundial Farm Antique Clocks Ltd..

Diese Abbildung ist urheberrechtlich geschützt und steht nicht unter einer freien Lizenz. Für anderweitige Nutzungen außerhalb von Watch-Wiki ist die schriftliche Zustimmung des Urheberrechtsinhabers nötig.


Dateiversionen

Klicke auf einen Zeitpunkt, um diese Version zu laden.

Version vomVorschaubildMaßeBenutzerKommentar
aktuell22:04, 15. Nov. 2016Vorschaubild der Version vom 22:04, 15. Nov. 2016435 × 856 (107 KB)Andriessen (Diskussion | Beiträge)German Carved Walnut Long-Running Conical Wall Regulator Clock, circa 1877 <br> Maker: Gebhard Bosch, Lübeck.<br> Description: A wonderful Victorian German long-running Conical Wall Regulator by Gebhard Bosch, Lübeck. The nicely proportioned glazed c…

Die folgende Seite verwendet diese Datei:

Metadaten